Job Type: Full Time
Experience: Minimum 3 Months Precision Mechanical Assembly and Test Experience
Job Overview: Apply finish coating to metal parts
Essential Duties and Responsibilities:
- Affix misc. metal parts to tooling racks to be coated
- Un-rack and package coated parts from tooling.
- Move racks of parts from station to station via carts.
- Regularly lift/move up to 25 lbs., frequently lift/move up to 50 lbs., and
occasionally lift/move up to 75 lbs.
- Must be able to work shifts for up to 10 hours where you are regularly
walking and standing.
- Working with sharps such as exacto, razor blades box cutters and some
tooling racks.
- Working around hot parts from baking and curing operations.
- Working around acids, caustics, solvents, paints and moving equipment.
Process Specific Duties - Powder Coating:
- Apply masking tape and trim using an exacto knife.
- Move carts in and out of oven on carts.
- Electrostatically spray powder onto parts in a filtered spray booth Affix
misc. metal parts to tooling racks to be coated
Process Specific Duties - Electro-Coating and Anodize:
- Place racked parts into wet process baths using overhead balancers
and or hoist.
- Using balancer or hoist, move racked parts down the line from tank to tank, applying electrical current to racks in some baths.
- Monitor electrical input to parts, bath temperatures and quality of rinse
and coatings applied.
- Dry parts with compressed air at end of process.
- Unload tooling racks from the process line onto specific carts, then load to
oven (Electro-Coat) or packaging (Anodize)
- Baths are all either DI water, alkaline or acidic in formulation, ranging
from 28F-150F in temperature, and from 84 to 300 gallons in volume.
Process Specific Duties - Screen Print:
- Mix and apply epoxy inks to parts
- Place printed parts on carts and move in and out of ovens to cure coating.
- Clean and re-store tools, products and equipment used.
Process Specific Duties - Laser Engrave:
- Place parts on specific tooling on the work turntable.
- While keeping clear of the engraving area, start process when complete
activate turn table to continue the second half of the operation.
- Once all parts are engraved, remove and reload turn table with the next lot of parts.
Required PPE Including but not limited to:
- Eye protection, hearing protection, gloves, respirator, boots, and aprons.
(duty dependent)
Qualification Requirements:
To perform this job successfully, upon completion of training, an individual
should be able to perform each essential duty satisfactorily. The requirements
listed below are representative of the education, experience, knowledge, skills
and/or ability required. Reasonable accommodations may be made to enable
individuals with disabilities to perform essential functions.
Education and/or Experience:
Minimum 3 months precision mechanical assembly and test experience.
Skills and Abilities
- Able to read and understand simple blueprints and manufacturing related documents such as manufacturing routers and equipment manuals.
- Able to add, subtract, multiply and divide whole numbers.
- Able to carry out instructions, and deal with problems involving concrete variables.
Physical Demands:
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodation may be made to enable individuals with disabilities to perform the essential functions.
While performing the duties of this job, the employee is frequently required to stand; walk; sit; use hands to finger, handle, or feel objects, tools or controls; talk or hear. The employee is occasionally required to reach with hands and arms, stoop, kneel, crouch or crawl. The employee must occasionally lift and/or move up to 30 lbs. Specific vision abilities required by this job include close vision, color vision, peripheral vision, depth perception and the ability to adjust focus.
Work Location: In person
Schedule: 8-hour shift
Pay: $16.90 - $18.50 per hour
Applicants must be eligible to work in the United States. Wilwood Engineering does not sponsor work visas. Cost of Relocation for Out of State Applicants not reimbursed.
